Building a boat involves a lot of firsts, and today was the first time we applied paint to the boat. We're using bright white Easypoxy for just about everything that isn't varnished until we sort out a final color scheme - likely white and grey. The outsides will be rolled and tipped, but for the insides we're just brushing.
The sections under the fore and aft decks is fair game for paint at this point as is the area under the seats. These are going to be too hard to get to once the decks and floors are glued on so we're painting them in advance.
We could have just left it with an epoxy coating but it seems prudent to protect the wood as well as possible in case any water works its way into the bilge. The paint is such a bright white it's hard to look at in the sunlight and kind of hard to photograph too. It should be fine for the topsides but it's giving us second thoughts about using it for the deck.
Once the paint dried a bit we flipped the hull over and started fairing around the keel to prep for fiberglassing. All the gaps around the keel are filled with thickened epoxy as well as fairing around the skeg.
The stem is also faired but we stopped short of where the rigging will attach using a heavy duty u-bolt. We put a smaller fillet at the u-bolt location to make room for the backing plates and will blend it into the rest of the stem fairing later.
The last bit of fairing was to tie the stem into the ends of the sheer stringers. Once the epoxy dries we can sand the corner down to make a nice curve.
We also used the extra bits of epoxy to fill the screw, staple and stitching holes. With a bit of sanding the hull should have a nice smooth surface for the fiberglass to lay over. We left some air bubbles in the keel fiberglassing that needed filling so it would be nice to prevent that on the hulls if we can.
This blog will document the construction and sailing adventures of a Hitia 17 beach cruising catamaran designed by James Wharram.
Monday, July 9, 2012
Thursday, June 28, 2012
Adirondack chairs - Part 2
Wife: "You know the fourth of July is next Wednesday right?"
Not much time left to get these chairs done! I picked up more wood from the lumber yard and got down to business.
Each seat back is slightly different so the bottom slats are cut based on the seat back width for that chair. From now on I'll have to keep these together, but since one is 1/16" of an inch wider than the other I should be able to tell from the fit. Using the seat slat stock as a guide, I clamped the bottom of the chair together and drilled for the cross braces. The front brace calls for #14 x 3" stainless steel screws which seem awfully big even to me.
Next the back two cross pieces are clamped, glued, and screwed together. These two cross pieces do not meet at 90 degrees and so the edges of the boards need to be adjusted to fit the angle.
Sounds like a great job to break in my new low angle block plane which handled the job beautifully.
All the holes were plugged just like before and then all the assembled pieces were sanded up to 220 grit. I'm using Deks Olje for the finish. It's a Scandinavian marine oil finish that fills the pores of the wood and leaves a semi-gloss finish once the surface of the wood is saturated. Another overkill step, but I want these chairs to last a long time and if it's good enough for wooden boat hulls it should be good enough for a lawn chair!
I hung up the chair bottoms from the dog run cable and brushed on the first coat. The cedar almost changes colors as you look from different angles. All the plugs have the grain oriented perpendicular to the surrounding grain so they really stand out.
Here they are after the second coat working by shop lights. From this angle the main boards appear lighter and the plugs darker.
It will probably take 6 coats or more to fill up the grain and get a nice even finish so I better keep at it.
Not much time left to get these chairs done! I picked up more wood from the lumber yard and got down to business.
Each seat back is slightly different so the bottom slats are cut based on the seat back width for that chair. From now on I'll have to keep these together, but since one is 1/16" of an inch wider than the other I should be able to tell from the fit. Using the seat slat stock as a guide, I clamped the bottom of the chair together and drilled for the cross braces. The front brace calls for #14 x 3" stainless steel screws which seem awfully big even to me.
Next the back two cross pieces are clamped, glued, and screwed together. These two cross pieces do not meet at 90 degrees and so the edges of the boards need to be adjusted to fit the angle.
Sounds like a great job to break in my new low angle block plane which handled the job beautifully.
All the holes were plugged just like before and then all the assembled pieces were sanded up to 220 grit. I'm using Deks Olje for the finish. It's a Scandinavian marine oil finish that fills the pores of the wood and leaves a semi-gloss finish once the surface of the wood is saturated. Another overkill step, but I want these chairs to last a long time and if it's good enough for wooden boat hulls it should be good enough for a lawn chair!
I hung up the chair bottoms from the dog run cable and brushed on the first coat. The cedar almost changes colors as you look from different angles. All the plugs have the grain oriented perpendicular to the surrounding grain so they really stand out.
Here they are after the second coat working by shop lights. From this angle the main boards appear lighter and the plugs darker.
It will probably take 6 coats or more to fill up the grain and get a nice even finish so I better keep at it.
Monday, June 25, 2012
Adirondack chairs - Part 1
I would have called this post "Adirondack chairs - the beginning" but this project started almost three years ago when I got plans and hardware for a pair of folding Adirondack chairs. Sure I could have just bought some chairs but wouldn't it be more fun to make them? And wouldn't they look so much nicer than store bought?
Well this project is off the back burner and will be done by the 4th of July so we can sit in them and watch fireworks. A while back I picked up some clear western red cedar boards and glued the plans onto plywood and cut out the shapes to use as templates.
I cut the WRC boards down roughly to shape back when I bought it but never finished shaping them. So the first step was to sit down with the jig saw for most of the day carefully tracing the patterns and cutting the parts.
Here is the hardware: #10 x 1 1/4", #10 x 2", and #14 stainless steel screws plus the stainless bolts that come with the hardware kit.
The bottom of the seat is made of boards glued up from two parts. The inner part holds the slats and the outer part is larger to cover the end grain of the seat slats
Here you can see how the seat slats will span between the two inner boars with the ends protected by the outer boards.
Next I started on the seat backs. The boards are clamped so that the screw holes can be drilled with a countersink bit. Then the joints are glued up and screwed together with #10 x 2" stainless steel screws.
The counter sink leaves a nice hole for a plug which will clean up the look of these chairs. This is way overkill but that's the fun of making instead of buying.
Plugs come from scraps which I was careful to keep since this cedar isn't cheap and I didn't want to waste any.
The plugs get a bit of glue and then pressed into place. It's the little details like this that I hope will set these apart when they are done and help them last a very long time.
I have run out of things to work on until I buy a couple more western red cedar boards so more to come soon.
Well this project is off the back burner and will be done by the 4th of July so we can sit in them and watch fireworks. A while back I picked up some clear western red cedar boards and glued the plans onto plywood and cut out the shapes to use as templates.
I cut the WRC boards down roughly to shape back when I bought it but never finished shaping them. So the first step was to sit down with the jig saw for most of the day carefully tracing the patterns and cutting the parts.
Here is the hardware: #10 x 1 1/4", #10 x 2", and #14 stainless steel screws plus the stainless bolts that come with the hardware kit.
The bottom of the seat is made of boards glued up from two parts. The inner part holds the slats and the outer part is larger to cover the end grain of the seat slats
Here you can see how the seat slats will span between the two inner boars with the ends protected by the outer boards.
Next I started on the seat backs. The boards are clamped so that the screw holes can be drilled with a countersink bit. Then the joints are glued up and screwed together with #10 x 2" stainless steel screws.
The counter sink leaves a nice hole for a plug which will clean up the look of these chairs. This is way overkill but that's the fun of making instead of buying.
Plugs come from scraps which I was careful to keep since this cedar isn't cheap and I didn't want to waste any.
The plugs get a bit of glue and then pressed into place. It's the little details like this that I hope will set these apart when they are done and help them last a very long time.
I have run out of things to work on until I buy a couple more western red cedar boards so more to come soon.
Subscribe to:
Posts (Atom)