We have been working on the boat since last June and today we are finally done with Sheet 1 of the plans! The hulls are now stitched together and ready for the bulkheads just in time for the warmer weather. We are pretty far along with other bits and pieces but we still haven't seen anything that looks like a boat, until today.
But before starting to stitch, we found mistake #3 with the bow panels. We made the top side too long which means the stem wouldn't fit. Something about the measurements on the plans didn't add up because the measurement from the edge of the ply was right, but the measurement from the bulkhead was wrong. You can see that we have to take off a small triangle from the front which was pretty easy with the pull saw, then used a chisel to bevel the edge of the butt block.
We also drilled the rudder lashing holes on the drill press before attaching the aft stems. These were a bit messy for our taste and so the next ones were done with a piece of wood clamped to the drill press table as a fence to keep the holes more neatly aligned.
And then it was time to start putting in stitches of copper wire! Here are the stitches along the bow. You can see how narrow the filler piece is now that we cut it down. The stitches in that area go through the main hull panel so we don't rip open that seam when the hulls are opened out.
We then stitched the aft stem and keel.
We couldn't help but open it up with one bulkhead and see what it will look like.
Check it out, it's a boat!
The bulkheads are just fit loose for now to see how they fit and if the stitches are the right tension. We will probably need to loosen the stitches along the keel to make sure it isn't twisted. Each additional bulkhead makes the shape prettier and prettier.
Unfortunately we will probably put the stitched hulls aside and go back to the beams and other small pieces while we wait for the fiberglass tape to be delivered and for a warm weekend day. Our plan is to do all the epoxy, fillets and fiberglass tape in one continuous process. It won't be this weekend and it won't be next weekend so perhaps the weekend after we'll have some glued up hulls.
This blog will document the construction and sailing adventures of a Hitia 17 beach cruising catamaran designed by James Wharram.
Thursday, March 29, 2012
Monday, March 12, 2012
Sheer stringers and more clamps
One thing we have learned is that gluing one floppy thing to another floppy thing means you're going to need a ton of clamps. Not wanting to spend the money on 30 or 40 spring clamps we went with the PVC clamp method.
It started with spending way too much time cutting 1" sections of 2" PVC pipe with a pull saw, then taking a short cut and using the circular saw, then realizing you have created a 10' radius of PVC chips in the yard and then finally shop-vac'ing your lawn to get it all cleaned up. But in the end we had plenty of clamps to get the hull sides ready for stitching.
Boston has finally warmed up enough that we can work outside again which was a treat after all that gluing in the basement. The stringers are held with the clamps and a few staples from the underside to keep them from sliding around. We also glued on the doubling blocks which go at the lashing points for the beams and mast stays.
We also glued the small extension on our replacement bow panels that we couldn't glue before while we had the chance. When these are dry we don't want anything to keep us from stitching up the hulls.
Here is hull side #2 sunning and hull side #3 glued and clamped up. By this point we have given each panel a final home as to which side of which hull they will become. Only the outside face of each hull gets the supports for the mast rigging so we put the two panels with the roughest seams on the inside where they will only be seen by the fishes.
The forecast says rain tomorrow morning but sun again in the afternoon so that should be enough of a window to glue the last hull side.
It started with spending way too much time cutting 1" sections of 2" PVC pipe with a pull saw, then taking a short cut and using the circular saw, then realizing you have created a 10' radius of PVC chips in the yard and then finally shop-vac'ing your lawn to get it all cleaned up. But in the end we had plenty of clamps to get the hull sides ready for stitching.
Boston has finally warmed up enough that we can work outside again which was a treat after all that gluing in the basement. The stringers are held with the clamps and a few staples from the underside to keep them from sliding around. We also glued on the doubling blocks which go at the lashing points for the beams and mast stays.
We also glued the small extension on our replacement bow panels that we couldn't glue before while we had the chance. When these are dry we don't want anything to keep us from stitching up the hulls.
Here is hull side #2 sunning and hull side #3 glued and clamped up. By this point we have given each panel a final home as to which side of which hull they will become. Only the outside face of each hull gets the supports for the mast rigging so we put the two panels with the roughest seams on the inside where they will only be seen by the fishes.
The forecast says rain tomorrow morning but sun again in the afternoon so that should be enough of a window to glue the last hull side.
Sunday, March 11, 2012
Mast gluing and details
There are a couple of small details that need to be taken care of so we can get to gluing. The mast foot is already shaped so that end is done but the top end of the mast needs some attention.
Here are the two masthead sheaves nearing completion. The grooves were shaped with a rat tail file and a little patience. all told these took about 20 minutes.
A test fit with 1/4" line which is size of the future main and jib halyards (halyard = rope that pulls up a sail).
The plans call for a space between the sheaves but didn't specify what so here is our answer: a 1/8" thick piece of douglas fir ripped on the table saw from some beam scraps. The two sides of are coated in epoxy since they will be hard to reach.
The whole unit is then glued together and ready to drop into corresponding cutouts in the mast halves.
We don't need these quite yet, but right to left shows the process or making the thumb cleats which will hold the stays at the top of the mast. The grain is oriented parallel to the outside edge for maximum strength even though the stays will be pulling toward the mast and downward. Who knows one day someone, probably me,f may try raising the mast by pulling on one and I'd like them to not break.
Which all lead up to the big event of gluing and clamping the mast halves together. I have quadrupled my army of bar clamps but still don't have as many as I would have liked for this job.
All told it came out nicely though and it's good to have the spars roughed out and ready for finishing when the rest of the boat is farther along. We're still waiting for the day when we have something that looks like a boat, hopefully that day will be here soon.
Here are the two masthead sheaves nearing completion. The grooves were shaped with a rat tail file and a little patience. all told these took about 20 minutes.
A test fit with 1/4" line which is size of the future main and jib halyards (halyard = rope that pulls up a sail).
The plans call for a space between the sheaves but didn't specify what so here is our answer: a 1/8" thick piece of douglas fir ripped on the table saw from some beam scraps. The two sides of are coated in epoxy since they will be hard to reach.
The whole unit is then glued together and ready to drop into corresponding cutouts in the mast halves.
We don't need these quite yet, but right to left shows the process or making the thumb cleats which will hold the stays at the top of the mast. The grain is oriented parallel to the outside edge for maximum strength even though the stays will be pulling toward the mast and downward. Who knows one day someone, probably me,f may try raising the mast by pulling on one and I'd like them to not break.
Which all lead up to the big event of gluing and clamping the mast halves together. I have quadrupled my army of bar clamps but still don't have as many as I would have liked for this job.
All told it came out nicely though and it's good to have the spars roughed out and ready for finishing when the rest of the boat is farther along. We're still waiting for the day when we have something that looks like a boat, hopefully that day will be here soon.
Subscribe to:
Posts (Atom)